Could not register user on sip.epygi.com - timeout error occurred

shipton · 11-01-2010, 01:31 PM

Every day all my snom handsets get the following error at some stage, usually all together but not always, and appears to be random times.

Could not Register user xxxxxxx on server sip.epygi.com:5060. Reason: Timeout occurred.
and approx 20s later i get -
Successfully registered user xxxxxx on server sip.epygi.com:5060

if the error occurs during a call it cuts it off. In the most recent case there was an error immediately before the top one saying - STUN port detection failure 6054;

All this seems to point to me that ports are being blocked or something.
my nat traversal settings are set to stun.epygi.com on port 3478.

On my vigor 2600 router i have open ports set on TCP 5060-5065 and UDP 5060-5065, and UDP 6000-6099 to point at the quadro ip address. there is no DMZ or port redirection set.
perhaps the vigor2600 is too old and long in the tooth for SIP ?

Can anyone advise - is this a handset thing or is it a nat issue?
I do see the message "Port Restricted Cone NAT" on the "SIP registration status" page.

hrant · 11-02-2010, 05:06 PM

Are you using the Epygi's SIP service for registering your SNOM phones directly?

shipton · 11-02-2010, 06:57 PM

yes. I can see all the extensions listed and registered on the epygi list when i log in, so i know they do actually register. Just very annoying being kicked off a call every now and then. When i go to the events i can see it is because of the timeout error/de-registering. sometimes there is a stun port error just before the timeout. possible that the broadband service blinks?

hrant · 11-02-2010, 07:10 PM

Do you have any Epygi Quadro device in your scenario?

stakano · 12-27-2010, 08:38 PM

Hi, I have the same issues across 3 devices on separate networks, all at the same time.

Is it coincidence that sip.epygi.com is getting timeouts? Is it getting a DoS attack?

nabilsaidou · 11-14-2011, 03:42 PM

hello, I have a problem with my DHCP Quadro 4x when I activate the DHCP seveur Quadro, it tells me that my server does not normally Started.
What could be causing the problem and how to solve it?
Thank you for your understanding

11-01-2010, 01:31 PM	#1
shipton Junior Member Join Date: Apr 2007 Location: Crieff Posts: 5	Could not register user on sip.epygi.com - timeout error occurred Every day all my snom handsets get the following error at some stage, usually all together but not always, and appears to be random times. Could not Register user xxxxxxx on server sip.epygi.com:5060. Reason: Timeout occurred. and approx 20s later i get - Successfully registered user xxxxxx on server sip.epygi.com:5060 if the error occurs during a call it cuts it off. In the most recent case there was an error immediately before the top one saying - STUN port detection failure 6054; All this seems to point to me that ports are being blocked or something. my nat traversal settings are set to stun.epygi.com on port 3478. On my vigor 2600 router i have open ports set on TCP 5060-5065 and UDP 5060-5065, and UDP 6000-6099 to point at the quadro ip address. there is no DMZ or port redirection set. perhaps the vigor2600 is too old and long in the tooth for SIP ? Can anyone advise - is this a handset thing or is it a nat issue? I do see the message "Port Restricted Cone NAT" on the "SIP registration status" page.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Remote User making calls our Epygi 4x	sring	Troubleshooting and Problems	6	11-11-2009 05:44 PM
Quadro 16x - Could not Register user 9522 on server 201.x.x.x:5060. Reason: Loop	DuettoFavorit	General Discussions	5	08-01-2009 09:05 PM
www.epygi-config.com - Error: This hostname does not resolve to this host!	crispeb	Troubleshooting and Problems	2	09-12-2008 11:13 AM
Increase Login timeout	ssteiner	General Discussions	3	11-08-2007 11:54 AM
Extensions don’t register on epygi.com	tinusroux	Installation	1	10-03-2007 08:39 PM

11-02-2010, 05:06 PM	#2
hrant Administrator Join Date: Sep 2006 Posts: 506	Are you using the Epygi's SIP service for registering your SNOM phones directly?

11-02-2010, 06:57 PM	#3
shipton Junior Member Join Date: Apr 2007 Location: Crieff Posts: 5	yes. I can see all the extensions listed and registered on the epygi list when i log in, so i know they do actually register. Just very annoying being kicked off a call every now and then. When i go to the events i can see it is because of the timeout error/de-registering. sometimes there is a stun port error just before the timeout. possible that the broadband service blinks?

11-02-2010, 07:10 PM	#4
hrant Administrator Join Date: Sep 2006 Posts: 506	Do you have any Epygi Quadro device in your scenario?

12-27-2010, 08:38 PM	#5
stakano Junior Member Join Date: Jul 2007 Posts: 29	Hi, I have the same issues across 3 devices on separate networks, all at the same time. Is it coincidence that sip.epygi.com is getting timeouts? Is it getting a DoS attack?

11-14-2011, 03:42 PM	#6
nabilsaidou Junior Member Join Date: Jan 2011 Posts: 3	hello, I have a problem with my DHCP Quadro 4x when I activate the DHCP seveur Quadro, it tells me that my server does not normally Started. What could be causing the problem and how to solve it? Thank you for your understanding

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)