Voice mail message sound is "dial tone" except words.

riskdata · 10-15-2008, 06:19 PM

We have in our company: Epygi FXOGW Firmware Version: 5.0.11/Release and Quadro4x IPPBX Firmware Version: 5.0.16/Release.
On FXOGW there ae rule in call routing that route all inbound calls on FXO2 port to extension 70 on IPPBX.
After missed call on FXO2 port if i check voicmail box of extension 70 there are appear new voice mail message, but i hear something like "dial tones" instead of some speech.

Have any idea?

AramK · 10-15-2008, 07:40 PM

Seems the FXO disconnect settings on FXOGW do not correspond to actual values of your local Telco you're renting the lines. Here are the steps suggested:

1. Check if your Locale is set to the country where the FXOGW is placed (assume it is France).
2. If the problem persists, send the voicemail from ext.70 with "dial tones" to Epygi tech Support. They will analize the tones and suggest correct disconnect values.

davrays · 10-20-2008, 05:09 PM

This is most probably the case.
If the voicemails you get on ext 70, are long (at least 20-30 seconds) and contain multiple periods of tone-silence, this (Aram's assumption) is definitely the case.

However, if the voice mails are short and contain just several seconds (and just one-two tine-silence periods), it means just that te caller didn't speak and put down the handset as soon as he listened the VM greeting. Short voicemail containing tones is a normal behaviour in such cases.

10-15-2008, 06:19 PM	#1
riskdata Junior Member Join Date: May 2007 Location: Paris Posts: 12	Voice mail message sound is "dial tone" except words. We have in our company: Epygi FXOGW Firmware Version: 5.0.11/Release and Quadro4x IPPBX Firmware Version: 5.0.16/Release. On FXOGW there ae rule in call routing that route all inbound calls on FXO2 port to extension 70 on IPPBX. After missed call on FXO2 port if i check voicmail box of extension 70 there are appear new voice mail message, but i hear something like "dial tones" instead of some speech. Have any idea?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fail reason: "Negotiation"	warren	Troubleshooting and Problems	3	08-25-2009 05:54 PM
la fonction "rappeler" du répondeur !	Jeanaug	Français	3	08-07-2008 09:23 AM
Dial "0" from Default A/A	KSComs	Suggestions and Feedback	7	04-07-2008 08:55 AM
Use built-in TFTP server to provision "Other" phones	mobidutch	Suggestions and Feedback	3	03-18-2008 02:37 PM
How to "transfer" calls between IP and analog lines?	mobidutch	'How Do I' Questions	4	03-17-2008 07:59 AM

10-15-2008, 07:40 PM	#2
AramK Senior Member Join Date: Sep 2006 Location: Yerevan Posts: 796	Seems the FXO disconnect settings on FXOGW do not correspond to actual values of your local Telco you're renting the lines. Here are the steps suggested: 1. Check if your Locale is set to the country where the FXOGW is placed (assume it is France). 2. If the problem persists, send the voicemail from ext.70 with "dial tones" to Epygi tech Support. They will analize the tones and suggest correct disconnect values.

10-20-2008, 05:09 PM	#3
davrays Quadro Architect Join Date: Jun 2006 Location: Around myself Posts: 2,083	This is most probably the case. If the voicemails you get on ext 70, are long (at least 20-30 seconds) and contain multiple periods of tone-silence, this (Aram's assumption) is definitely the case. However, if the voice mails are short and contain just several seconds (and just one-two tine-silence periods), it means just that te caller didn't speak and put down the handset as soon as he listened the VM greeting. Short voicemail containing tones is a normal behaviour in such cases.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)