Quadro isdn to from elastix server

[equintana]

Hi,


I have purchased a quadro isdn, installed elastix into a new server and new cisco spa 504 ip phones.


I configured an isdn line to test in/out phone call. Tomorrow I´ll install spanish language.


How can I route in/out phone calls to the elastix server.??


regards

[equintana]

hi,

any idea?

[hrant]

You have to create two records in Call Routing table. One for the calls from ISDN to SIP and the second for the calls from SIP to ISDN. Also, in ISDN configuration be sure to send the inbound calls to Call Routing. The configuration details check in the document

[equintana]

HI,


I changed the elastix option to 3cx. But still having some problems to route in/out calls.

any idea?

[hrant]

it doesn'm matter if it is elastix or 3cx. Yoiu have to configure the Call Routing rules on Quadro as i explained before.

[equintana]

HI,

I folloewd this post: http://www.3cx.com/forums/configurin...sdn-17202.html, see the image call routing table.

I configured 2 enabled lines.

I also configured at 3cx outbound calls....

When I call using an external phone to the isdn line at log I can see:

21-dic-2010 18:31:51 PSTN0/1-0xxxxxxxxxxxx(system/CR) NTelefonoRDSI@192.168.157.134:5060 "User Not Found".

Must I register the 4 isdn port at 3cx?

[equintana]

Resumen - Editar Adición


Tipo de Enrutamiento de Llamadas
Patron: *
Numero de simbolos descartados:
Prefijo:
Sufijo:
Tipo de Llamada: IP-PSTN
Metrico: 10
Descripción:
configuracion de Enrutamiento de llamadas
Use la configuracion de Extensiones:
Mantener el Caller ID original: No
Agregar ID del extremo Remoto: No
Puerto de Destino: 192.168.157.213
Puerto de Destino: 5060
Nombre de Usuario:
Protocolo de Transporte para SIP: UDP
Restrict the Number of Simultaneous Calls: No
Use el proxy RTP: No
Temporizador de Actividad: Deactivado
AAA Requerido: AAA deshabilitada.
Failover Reason(s): Ninguno

Informacion de Fuente de Ruteo de LLamada
Discard Non-Numeric Symbols: No
Patron de llamada entrante: *
Tipo de llamada entrante: ISDN
Puerto ID de entrada: Cualquier puertor puerto
Timeslots de entrada: 1,2
Inbound Caller ID Modification
Numero de simbolos descartados:
Prefijo:

[equintana]

esumen - Editar Adición


Tipo de Enrutamiento de Llamadas
Patron: *
Numero de simbolos descartados:
Prefijo:
Sufijo:
Tipo de Llamada: ISDN
Metrico: 10
Descripción:
configuracion de Enrutamiento de llamadas
Mantener el Caller ID original: Sí
ID de Puerto: Cualquier puerto (Usuario)to (Usuario)
Timeslots: 1,2
AAA Requerido: AAA deshabilitada.
Failover Reason(s): Ninguno

Informacion de Fuente de Ruteo de LLamada
Discard Non-Numeric Symbols: No
Patron de llamada entrante: *
Tipo de llamada entrante: PBX
Inbound Caller ID Modification
Numero de simbolos descartados:
Prefijo:


shows as invalid entry!!!!! why?

[artur_s]

An "invalid" is displayed beside the ISDN routing pattern if the ISDN User/Network mode selection from ISDN Settings have been changed since creating the corresponding route. Invalid ISDN patterns will not take effect so you have to reedit Invalid call routing rules.

[equintana]

Hi,

And which rules must be configured to route call from 3cx to epygi and then to isdn lines?

There are no epygi experience with 3cx yes with beronet and beyond!!


what about the pst-0 identifier every incoming call?