Trouble with Remote phone, strange occurances

[ptemplin7]

Hi all,

I know this is one of those topics that there is a lot posted. I have read most but still can't figure out what is wrong. Also have done a lot of testing a tweaking.

Here's the setup.
2 remote phones, both Snom 360's
1 works great one has issues.

Quadro is behind a firewall. Calls to it and regular extensions working fine.
Remote that is working is behind a basic Linksys router.
Snom set up with external register, Quadro set to handle RTP proxy and Symmetrical RTP.
Stun is not in use. RTP port 49150-60, sip via 5060

Remote not working configured exactly the same execpt behind a clearOS server/Firewall. sip_nat_ip module disable.
Phone is set up identically except for username and password.

Here's the strange part.
Phone registers fine.
Phone can call internal extension fine.
phone can call outside fine.
Calls to phone get the blank air for 25 seconds and then drop into voicemail.
Sip trace shows call never gets to the phone. Quadro sip log shows the invites going out but no answer.

Does anyone have any suggestions for correcting this. (Note I have had it work the exact opposite way as well. No calls out, all calls in working!)
This phone used to work for both incoming and outgoing calls. The firewall crashed and network was upgraded by DSL provider. Suggestions?
Thanks, Paris

[Alloy Service]

Hi,

I ve got the same issue.
My customer is using a Quadro 4x on the main site, and multi remote extension all across australia (~10).
Everything works fine during 18months but they had a power outage on the main site, nothing big just a cut during few hours.
After the Quadro reboot the issue appeared for all the remote extension connected.

telephony design :
Main site : DSL router on bridge mode>wan port of Quadro 4x>lan port to POE switch>Snom phones
Remote site : dsl modem/router>snom 300 phone. Port forwarding ok on all routers :SIP : 5060tcp/udp, RTP : UDP 6000 to 6100

ISSUE :
All RE are registered fine and can make outbound/inbound calls and also call/received calls from the local extension from the main site.
But when you try to make calls between RE it goes straight to the voicemail.
After ages of testing, it looks like the quadro couldn't find registered the called RE so it forward to the voice mail. But there are all registered!!!
The worst is, I set up a remote extension on my office connected to the Quadro of the customer, and during the first hour it worked perfectly. but after more that an hour, when I called from another RE, it went to the voicemail.

I'm sure that is a NAT/ network issue but it s too deep for me. It s look like there is a timeout in the network somewhere which deny the incoming call from another RE.
The thing is everything worked find during 18 months, no changes were made.

Is there anyone got an idea ?

Thanks,

Thomas

[dogcom]

hey thomas
what version firmware are u running?
what stun server are u using?
are u using nat static address?
i'll call u tomorrow ok?
cheers

[KSComs]

Padawan becomes the Master



Must have a good teacher

[Alloy Service]

Tks guys,

I finally resoleve this issue by doing this :

-DSL/Router or firewall on the remote sites :
Those ports forwarding have to be configure for the NAT :
SIP : 5060 to 5070 forward to the @IP of the IP phone
RTP : 6000 to 6100 forward to the @IP of the IP phone
STUN : 3478 to 3479 forward to the @IP of the IP phone

-User extension (remote extension settings) :
Enable RTP proxy
Symetric RTP ticked

-On the IP Phone web page settings :
For SNOM :
*NAT Identity Settings :
Offer ICE : on
STUN server : stun.epygi.com:3478
STUN interval : 300
STUN timeout : 120
*Registration timeout (Identity > SIP) :
Proposed Expiry : 300
Reboot the phone

And it works fine, don t know for how long!!!!hope forever

cheers,

toma