Call Park

andy.collins · 02-09-2008, 06:52 PM

Hi

I am using the call park facility *5 which works fine until another call comes in while a call is parked. I am then unable to retrieve the parked call.

Can anyone help?

thanks

Andy

AramK · 02-10-2008, 12:07 PM

Andy, can you describe your problem a little bit detailed ? Where the second call is coming - to the Park Extension or where ?

andy.collins · 02-10-2008, 04:47 PM

Hi Aram

After further testing.

A call arrives via ISDN and is parked, this can be unparked by dialling the call park extension (39) without a problem. However, whilst a call is parked if another call arrives and is active on another extension when I unpark the call a message on the Snom says 'Held By: 39' (39 being the call park), I can hear the caller but they cannot hear me, it is as if mute has been used. If the 1st call remains parked and the 2nd call is completed then i can unpark no problem.

I hope this makes sense to you as it is difficult to explain. Thank you

Andy

AramK · 02-11-2008, 12:16 PM

Hi Andy. Sorry, I wasn't able to reproduce your scenario here in our testlab. The problem may be connected to your ISDN provider or some specific settings on your Quadro. Could you please reproduce the scenario once again, download the Quadro systemlogs and open a TSS ticket (or ask Matt to do so). We'll examine the logs and your Quadro config and will back with answer/solution.

andy.collins · 02-12-2008, 07:36 AM

Hi Aram

I think there is a problem with my Quadro config. The 'Held by:' message is also displayed after i have been on an incoming call for around 5 minutes. Outbound is fine. Does this help or would you still like the logs?

Thank you

Andy

AramK · 02-12-2008, 07:45 AM

Andy, in any case logs would be very useful, but now I suspect your Snom phone. How is it configured ? What is the firmware version of Snom ? Do you have the same behaviour on other Snom phone ? Please check also the Session Timer settings both on Quadro and Snom.

andy.collins · 02-12-2008, 08:20 AM

Hi Aram

I am not sure if it is confined to one snom although session timer was being used on the particular extension i had the problem with. This has now been removed and i will test and let you know. The Snom is on 6.5.17 and auto provisioned.

Thank you

Andy

AramK · 02-12-2008, 08:51 AM

OK Andy, the Session Timer can be a reason of such problem. Please inform us about the results. If this will not solve your problem, then we'll definitely need Quadro systemlogs for further investigation.

02-09-2008, 06:52 PM	#1
andy.collins Member Join Date: Dec 2006 Location: Uckfield Posts: 35	Call Park Hi I am using the call park facility *5 which works fine until another call comes in while a call is parked. I am then unable to retrieve the parked call. Can anyone help? thanks Andy

02-10-2008, 04:47 PM	#3
andy.collins Member Join Date: Dec 2006 Location: Uckfield Posts: 35	Hi Aram After further testing. A call arrives via ISDN and is parked, this can be unparked by dialling the call park extension (39) without a problem. However, whilst a call is parked if another call arrives and is active on another extension when I unpark the call a message on the Snom says 'Held By: 39' (39 being the call park), I can hear the caller but they cannot hear me, it is as if mute has been used. If the 1st call remains parked and the 2nd call is completed then i can unpark no problem. I hope this makes sense to you as it is difficult to explain. Thank you Andy Last edited by andy.collins : 02-10-2008 at 05:47 PM.

02-12-2008, 07:45 AM	#6
AramK Senior Member Join Date: Sep 2006 Location: Yerevan Posts: 796	Andy, in any case logs would be very useful, but now I suspect your Snom phone. How is it configured ? What is the firmware version of Snom ? Do you have the same behaviour on other Snom phone ? Please check also the Session Timer settings both on Quadro and Snom. Last edited by aramk : 02-12-2008 at 07:47 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Direct call park	ssteiner	'How Do I' Questions	14	11-05-2007 12:36 PM
Call Park from IP Phone	threebit	'How Do I' Questions	2	07-05-2006 07:52 PM

02-10-2008, 12:07 PM	#2
AramK Senior Member Join Date: Sep 2006 Location: Yerevan Posts: 796	Andy, can you describe your problem a little bit detailed ? Where the second call is coming - to the Park Extension or where ?

02-11-2008, 12:16 PM	#4
AramK Senior Member Join Date: Sep 2006 Location: Yerevan Posts: 796	Hi Andy. Sorry, I wasn't able to reproduce your scenario here in our testlab. The problem may be connected to your ISDN provider or some specific settings on your Quadro. Could you please reproduce the scenario once again, download the Quadro systemlogs and open a TSS ticket (or ask Matt to do so). We'll examine the logs and your Quadro config and will back with answer/solution.

02-12-2008, 07:36 AM	#5
andy.collins Member Join Date: Dec 2006 Location: Uckfield Posts: 35	Hi Aram I think there is a problem with my Quadro config. The 'Held by:' message is also displayed after i have been on an incoming call for around 5 minutes. Outbound is fine. Does this help or would you still like the logs? Thank you Andy

02-12-2008, 08:20 AM	#7
andy.collins Member Join Date: Dec 2006 Location: Uckfield Posts: 35	Hi Aram I am not sure if it is confined to one snom although session timer was being used on the particular extension i had the problem with. This has now been removed and i will test and let you know. The Snom is on 6.5.17 and auto provisioned. Thank you Andy

02-12-2008, 08:51 AM	#8
AramK Senior Member Join Date: Sep 2006 Location: Yerevan Posts: 796	OK Andy, the Session Timer can be a reason of such problem. Please inform us about the results. If this will not solve your problem, then we'll definitely need Quadro systemlogs for further investigation.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)