redirect all incoming calls to outside number

mjnorris · 08-04-2008, 04:19 AM

I need to temporarily divert all incoming calls to an outside line that is not connected to the Quadro at all..

How do I do this?

AramK · 08-04-2008, 07:53 AM

First of all you current configuration is needed. Are all your incoming calls routed to some particular extension. If no, then you need to route all your calls to one extension. Then you need to configure Unconditional Call Forwarding to the "outside line" mentioned by you. To setup forwarding you need to go to the Supplementery Services page, that is placed under extension.

sjet701 · 08-12-2008, 07:35 AM

Further to the above, I have found the *4 feature a excellent way to enable the user to activate diversion from the target extension. Thats the ability to toggle on & off from the an Extension.

davrays · 08-20-2008, 08:28 PM

A good way to redirect *REALLY ALL* (regardless of origin, destination or anything else) incoming calls to some place:
a) set the "Route all calls to Call Routing",
b) route all PSTN calls (FXO or ISDN depending on device flavour) to "Routing" with any pattern (do that from "FXO Settings" or "ISDN Settings" page
c) disable all routing records, then add one record with pattern "*" (asterisk), and route that wherever you would like to

This is a bit rough way, which a few people could use (mostly the ones who understand what Quadro is capable to do

) but it ensures that *everything*, passing through device, will be redirected

Best regards,
David

08-04-2008, 04:19 AM	#1
mjnorris Member Join Date: Nov 2007 Location: Japan Posts: 47	redirect all incoming calls to outside number I need to temporarily divert all incoming calls to an outside line that is not connected to the Quadro at all.. How do I do this?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Number of calls per proxy	ssteiner	'How Do I' Questions	14	02-11-2008 11:36 AM
differentiate between incoming calls	t_h_048d3	'How Do I' Questions	2	09-17-2007 05:02 PM
Incoming SIP Calls Fail	baoan	Troubleshooting and Problems	5	04-30-2007 12:53 AM
Limiting the number of calls out a ITSP	Zarf!	Suggestions and Feedback	0	03-19-2007 12:58 PM
Lag time in incoming calls	etolentino	Troubleshooting and Problems	5	01-16-2007 07:43 PM

08-04-2008, 07:53 AM	#2
AramK Senior Member Join Date: Sep 2006 Location: Yerevan Posts: 796	First of all you current configuration is needed. Are all your incoming calls routed to some particular extension. If no, then you need to route all your calls to one extension. Then you need to configure Unconditional Call Forwarding to the "outside line" mentioned by you. To setup forwarding you need to go to the Supplementery Services page, that is placed under extension.

08-12-2008, 07:35 AM	#3
sjet701 Member Join Date: Jun 2006 Location: Brisbane, Australia Posts: 31	Further to the above, I have found the *4 feature a excellent way to enable the user to activate diversion from the target extension. Thats the ability to toggle on & off from the an Extension.

08-20-2008, 08:28 PM	#4
davrays Quadro Architect Join Date: Jun 2006 Location: Around myself Posts: 2,083	A good way to redirect REALLY ALL (regardless of origin, destination or anything else) incoming calls to some place: a) set the "Route all calls to Call Routing", b) route all PSTN calls (FXO or ISDN depending on device flavour) to "Routing" with any pattern (do that from "FXO Settings" or "ISDN Settings" page c) disable all routing records, then add one record with pattern "" (asterisk), and route that wherever you would like to This is a bit rough way, which a few people could use (mostly the ones who understand what Quadro is capable to do ) but it ensures that everything*, passing through device, will be redirected Best regards, David

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)